Contents
Spinning fishing technique involves several types of lure postings. Wiring, in general, plays a very important role in the performance of spinning fishing. No matter how good and high-quality the lure is, it must be able to be carried correctly in the water column so that the predator decides to attack. It is the wiring that makes the game of the bait attractive to the predator.
wiring yekreng
This is the easiest way of wiring, which is used when catching fish. The wiring technique is based on uniform winding of the fishing line with a reel. Apart from the reel, no part of the rod takes part in the game of the lure. In this case, only the speed of the bait can be regulated, and the depth of its immersion depends on the speed. Fast wiring is suitable for fishing at shallow depths, when the bait moves in the upper layers of the water. Slower wires are used when fishing at depths, and the slower the wire, the deeper the bait can be pulled. There are baits, such as spinners, that keep the real game only when the wiring is even. Most other baits and spinners can be carried out with any kind of wiring.
wiring nehevseng
Uneven wiring involves slowing down or accelerating the movement of the bait during its movement, as well as the formation of pauses between these irregularities. Suitable for using any bait, but such wiring is especially effective when using oscillating lures.
Têlkirina gavê
Stepped wiring consists of separate steps, when the bait sinks to the bottom, after which it is lifted from the bottom, and then lowered again, but not to the bottom, but a little higher. And so, step by step, with a slow rise, wiring is carried out. This type of wiring is great for fishing with wobblers, spoons and jig lures.
Twitching
This type of wiring is designed for catching predatory fish with baits such as a wobbler. Twitching is a jerky type of wiring, which is carried out with the help of sharp movements of the rod in one direction or the other. Twitching can be low-amplitude, medium-amplitude and high-amplitude, depending on the fishing conditions. At the same time, the wobbler moves in jerks, changing direction, and its movements resemble a weak, wounded fish. Such movements with bait make even the laziest predator react to the game of the wobbler. For this type of wiring, you should choose a powerful spinning rod, from 2 to 2,4 meters long. It is better to take a braided fishing line so that the jerks are pronounced. There are many options for twitching, but it is very important to choose the right wobbler so that it is narrow-bodied and driven.
Hard monotonous twitching involves high-amplitude movements of the rod. The amplitude of movement is up to 60 cm. Between jerks, the line is wound up with a reel.
Hard chaotic twitching – jerks and pauses are different every time.
Hard twitching with pauses – after 3-4 jerks, a pause of 3-4 seconds is made.
Soft twitching – small amplitude movements are made with a rod with acceleration or deceleration.
Rawestan&Go – slow movements with the rod, which are accompanied by winding the reel: 3-4 turns of the reel – 3-4 seconds of pause.
jig wiring
This wiring is carried out using a hard spinning rod and a braided cord. Jig wiring is a kind of fishing technique using jig baits. With the advent of jig lures, the approach to fishing itself has changed significantly. There are several types of such wires.
classic wiring
This is active high-speed wiring, which is carried out using a coil. The bait is cast, after which a pause is made so that the bait sinks to the bottom. After that, several turns are made by the coil, followed by a pause. During this time, usually up to 4 seconds, the jig again falls to the bottom. It is during the pause, when the bait is in a state of free fall, that most bites occur. As soon as the bait reaches the bottom, the wiring continues again, while the number of revolutions of the coil can be increased or decreased, as well as the duration of the pause. This process is repeated until the bait approaches the shore. After that, if the bite did not occur, you can again cast the bait. You should not fish for a long time in the same place. If after 3 or 5 casts no bites followed, then you can move on to the next place.
slow wiring
If the predator is not active, then you can use slow wiring, when the time for the jig to fall to the bottom is limited to 1-2 seconds, with a wiring length of 1-2 meters. This type of wiring requires the use of light baits, weighing up to 7 grams. Such baits are very difficult to control. As a rule, such lures require the use of rods with a test of up to 10 grams.
American wiring
The meaning of American wiring is that the movements of the bait are carried out by a rod, and not by a reel, as in the classic version. After the next fall of the bait to the bottom, the line is reeled up with a reel. Depending on the fishing conditions, the length of the rod is also selected. The longer the rod, the more step you can make. A small rod will not allow this. After each touch of the bottom with the bait and the selection of the fishing line, another pull-up is performed with the rod.
American wiring is more sensitive to the bait, since its movement is controlled during pull-ups. In this case, the bait, fishing line, rod and hand of the spinning player become one.
Video “Technique for casting bait with spinning”
The technique of casting lures with a spinning rod
Spinning fishing is the most active fishing and the most interesting form of leisure. As a rule, a spinner in search of predatory fish can walk several kilometers a day, unlike other fishermen who sit on the shore for days.